Sawaal
  • Home/
  • Searching for configured

 Searching for "configured"

Q:

How should a router that is being used in a Frame Relay  network be configured to keep split horizon issues from preventing routing updates

A) Configure a seperate subinterface for each PVC with a unique DLCI and subnet assigned to the subinterface B) Combine multiple Frame Relay circuits as a point-to-point line to support multicast and broadcast traffic
C) Configure many subinterfaces in the same subnet D) Configure a single subinterface to establish multiple PVC connections to multiple remote router interfaces.
 
Answer & Explanation Answer: A) Configure a seperate subinterface for each PVC with a unique DLCI and subnet assigned to the subinterface

Explanation:

If you have a serial port configured with multiple DLCIs connected to multiple remote sites, split horizon rules stop route updates received on an interface from being sent out the same interface. By creating subinterfaces for each PVC, you can avoid the split horizon issues when using Frame Relay.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

Q:

You have finished physically installing an access point on the ceiling of your office. At a minimum, which parameter must be configured on the access point in order to allow a wireless client to operate on it?

A) AES B) PSK
C) SSID D) WEp
 
Answer & Explanation Answer: C) SSID

Explanation:

The minimum parameter configured on an AP for a simple WLAN installation is the SSID, although you should set the channel and authntication method as well.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

Q:

A switch has been configured configured for three different VLANs : VLAN2, VLAN3 and VLAN4. A router has been added to provide communication between the VLANs. What minimum type of interface necessary on the router if only one connection is to be made between the router and the switch?

A) 10Mbps Ethernet B) 56Kbps Serial
C) 100Mbps Ethernet D) 1Gbps Ethernet
 
Answer & Explanation Answer: C) 100Mbps Ethernet

Explanation:

Although you can use either 100Mbps or 1Gbps Ethernet, the 100Mbps is necessary at a minimum and is the best answer to this question. You need to trunk the link from the switch to the router to make this connection work with inter-VLAN communication.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

Q:

If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a  loopback interface?

A) The Lowest IP address of any physical interface B) The Highest IP address of any physical interface
C) The Lowest IP address of any logical interface D) The Highest IP address of any logical interface
 
Answer & Explanation Answer: B) The Highest IP address of any physical interface

Explanation:

At the moment of OSPF process startup, the highest IP address on any active interface will be the Router ID (RID) of the router . If you have a loopback interface configured (logical interface), then that will override the interface IP address and become the RID of the router automatically.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

Q:

Two connected routers are configured only with RIP routing. What will be the result when a router receives a routing update that contains a higher-cost path to a network already in its routing table?

A) The updated information will be added to the existing routing table B) The update will be ignored and no further action will occur
C) The updated information will replace the existing routing table entry D) The existing routing table entry will be deleted from the routing table and all routers will exchange routing updates to reach convergence
 
Answer & Explanation Answer: B) The update will be ignored and no further action will occur

Explanation:

When a routing update is received by a router, the router first checks the administrative distance (AD) and always chooses the route with the lowest AD. However, if two routes are received and they both have the same AD and differing metrics , then the router will choose the one route with the lowest metrics or , in RIP's case, hop count.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

Q:

What must be configured on the network in order for users on the Internet to view web pages located on Web Server 2?

A. On router R2, configure a default static route to the 192.168.10.0 network
B. On router r2, configure DNS to resolve the URL assigned to Web Server 2 to the 192.168.10.20 address
C. On router R1, configure NAT to translate an address on the 209.165.100.0/24 network to 192.168.10.20
D. On router R1, configure DHCP to assign a registered IP address on the 209.165.100.0/24 network to Web Server 2

Answer

Answer : C

Report Error

View answer Workspace Report Error Discuss

Subject: CCNA

Q:

An administrator issues the command

A. The PC host PC1 has connectivity with a local host
B. The PC host PC1 has connectivity with a Layer 3 device
C. The PC host PC1 has a default gateway correctly configured
D. The PC host PC1 has connectivity up to Layer 5 of the OSI model
E. The PC host PC1 has the TCP/IP protocol stack correctly installed

Answer

Answer : E


Explanation:


The “ping 127.0.0.1″ command is used to troubleshoot the local network card and the TCP/IP stack to make sure is working correctly. If an ICMP echo reply is received, that shows there are connectivity to a particular host in the network.


 

Report Error

View answer Workspace Report Error Discuss

Subject: CCNA

Q:

Your network consists of a single Active Directory domain named contoso.com. The functional level of the domain is Windows Server 2003. You have a file server named Server1 that is used to store users' home folders and profiles. On Server1, you create a folder named D:data and share the folder as UserData. You create a new user account named TemplateUser in Active Directory. You need to ensure that each user account you create by copying TemplateUser is configured to have a unique home folder stored in the UserData share. Which home folder path should you specify?

A) D:\data\%homedrive% B) D:\data\%username%
C) \\server1\userdata\%homedrive% D) \\server1\userdata\%username%
 
Answer & Explanation Answer: D) \\server1\userdata\%username%

Explanation:
Report Error

View Answer Report Error Discuss

Filed Under: MCSA-Microsoft Certified Solutions Associate