Sawaal

 CISCO Certification Questions

Popular Latest Rated
Q:

How should a router that is being used in a Frame Relay  network be configured to keep split horizon issues from preventing routing updates

A) Configure a seperate subinterface for each PVC with a unique DLCI and subnet assigned to the subinterface B) Combine multiple Frame Relay circuits as a point-to-point line to support multicast and broadcast traffic
C) Configure many subinterfaces in the same subnet D) Configure a single subinterface to establish multiple PVC connections to multiple remote router interfaces.
 
Answer & Explanation Answer: A) Configure a seperate subinterface for each PVC with a unique DLCI and subnet assigned to the subinterface

Explanation:

If you have a serial port configured with multiple DLCIs connected to multiple remote sites, split horizon rules stop route updates received on an interface from being sent out the same interface. By creating subinterfaces for each PVC, you can avoid the split horizon issues when using Frame Relay.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

22 14484
Q:

Which of the following describes the creation of private networks across the Internet, enabling privacy and tunneling of non-TCP/IP protocols?

A) HDLC B) Cable
C) VPN D) IPSec
 
Answer & Explanation Answer: C) VPN

Explanation:

A VPN allows or describes the creation of private networks across the Internet, enabling privacy and tunneling of non-TCP/IP protocols. A VPN can be set up across any type of link.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

22 14375
Q:

Which OSI layer defines the standards for cabling and connectors?

A) Layer 1 B) Layer 4
C) Layer 7 D) Layer 3
 
Answer & Explanation Answer: A) Layer 1

Explanation:

OSI layer 1 defines the standards for cabling and connectors.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA
Job Role: Network Engineer

31 14213
Q:

You want to implement a mechanism that automates the IP configuration, including IP address, subnet mask, default gateway, and DNS information. Which protocol will you use to accomplish this?

A) SMTP B) SNMP
C) DHCP D) ARP
 
Answer & Explanation Answer: C) DHCP

Explanation:

Dynamic Host Configuration Protocol (DHCP) is used to provide IP information to hosts on your network. DHCP can provide a lot of information, but the most common is Ip address, subnet mask, default gateway, and DNS information.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

2 13480
Q:

What does the command confreg 0x2142 provide?

A) It is used to restart the router B) It is used to bypass the configuration in NVRAM
C) It is used to enter ROM monitor mode D) It is used to view the lost password
 
Answer & Explanation Answer: B) It is used to bypass the configuration in NVRAM

Explanation:

The default configuration setting is 0x2102, which tells the router to load the IOS from flash and the configuration from NVRAM. 0x2142 tells the router to bypass the configuration in NVRAM so that you can perform password recovery.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

2 13295
Q:

Which of the following is an industry-wide standards suite of protocols and algorithms that allows for secure data transmission over an IP-based network that functions at the layer3 Network layer of the OSI model?

A) HDLC B) xDSL
C) VPN D) IPSec
 
Answer & Explanation Answer: D) IPSec

Explanation:

IPSec is an industry-wide standard suite of protocols and algorithms that allows for secure data transmission over an IP-based network that functions at the layer3 Network layer of the OSI model.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

24 13117
Q:

A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20684570. Another route is from OSPF with a metric of 852. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?

A. the OSPF route
B. the EIGRP route
C. the RIPv2 route
D. all three routes
E. the OSPF and RIPv2 routes

Answer

Answer : B


Explanation :


This is one of those tricky questions just to test your knowledge of routing protocols and their administrative distance. Let’s look at the AD of popular routing protocols below:
 Routing Protocol (Source)                           AdministrativeDistance(AD)                                                             


  Directly connected                                        0


  Static Route                                                  1


  EIGRP                                                           90


  Summary Route(EIGRP)                              5


  OSPF                                                           110


  RIP                                                              120


Fom the above table, you can see that EIGRP has the lowest AD from all of the above mentioned routing protocols. So, the router will choose to use the routing protocol which has lowest Administrative Distance which in this case is B. EIGRP

Report Error

View answer Workspace Report Error Discuss

Subject: CCNA

4 12926
Q:

By default , what type of trust are all Windows 2000 trust relationships within a domain tree or forest?

A) Explicit trust B) One-way trust
C) Transitive trust D) Non-transitive trust
 
Answer & Explanation Answer: C) Transitive trust

Explanation:

By default, all Windows 2000 trusts within a domain tree or forest are transitive trusts.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

25 12692