Sawaal

 CCNA Questions

Popular Latest Rated
Q:

When a ping to the loopback address fails , what can you assume?

A) The IP address of the local host is incorrect B) The IP address of the remote host is incorrect
C) The NIC is not functional D) The IP stack has failed to initialize
 
Answer & Explanation Answer: D) The IP stack has failed to initialize

Explanation:

When a ping to the loopback address fails , you can assume the IP stack has failed to initialize.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 3324
Q:

What network service is the most likely problem if you can ping a computer by IP address but not by name?

A) DNS B) DHCP
C) ARP D) ICMP
 
Answer & Explanation Answer: A) DNS

Explanation:

 The most likely problem if you can ping a computer by IP address but not by name is a failure of DNS.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 3323
Q:

A default Frame Relay WAN is classified as what type of physicalnetwork?

A: broadcast point-to-multi point
B: broadcast multi-access
C: non broadcast multi-access
D: non broadcast multi-point

Answer

Answer : C


Explanation:


FrameRelay, ATM, and X.25 are non-broadcast multiple access (NBMA) networks. NBMA networks allow only data transfer from one computer to another over a VC or across a switching device. NBMA networks do not support multicast or broadcast traffic


FrameRelay, ATM, and X.25 are non-broadcast multiple access (NBMA) networks. NBMA networks allow only data transfer from one computer to another over a VC or across a switching device. NBMA networks do not support multicast or broadcast traffic - See more at: https://www.orbitco-ccna-pastquestions.com/CCNA-Past-Questions%3A-WAN.php#sthash.hb05ZKYs.dpuf
Report Error

View answer Workspace Report Error Discuss

Subject: CCNA

2 3270
Q:

What four routed protocols are supported by EIGRP?

Answer

The four routed protocols supported by EIGRP are IP, IPv6, IPX, and AppleTalk.

Report Error

View answer Workspace Report Error Discuss

Subject: CCNA

1 3219
Q:

If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a  loopback interface?

A) The Lowest IP address of any physical interface B) The Highest IP address of any physical interface
C) The Lowest IP address of any logical interface D) The Highest IP address of any logical interface
 
Answer & Explanation Answer: B) The Highest IP address of any physical interface

Explanation:

At the moment of OSPF process startup, the highest IP address on any active interface will be the Router ID (RID) of the router . If you have a loopback interface configured (logical interface), then that will override the interface IP address and become the RID of the router automatically.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 3207
Q:

Which command displays RIP routing updates?

A) Show ip route B) debug ip rip
C) show protocols D) Debug ip route
 
Answer & Explanation Answer: B) debug ip rip

Explanation:

Debug ip rip is used to show the internet Protocol (IP) Routng Information protocol (RIP) updates being sent and received on the router.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 3200
Q:

Which of the following commands will configure all the default VTY ports on a router?

A) Router#line vty 0 4 B) Router (config) #line vty 0 4
C) Router (config-if)#line console 0 D) Router(config)#line vty all
 
Answer & Explanation Answer: B) Router (config) #line vty 0 4

Explanation:

From global configuration mode, use the line vty 0 4 command to set all five default VTY lines

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 3169
Q:

Which mask should you use on point-to-point WAN links in order to reduce the waste of IP addresses?

A) /28 B) /29
C) /30 D) /31
 
Answer & Explanation Answer: C) /30

Explanation:

A point-to-point link uses only two hosts. A/30, or 255.255.255.252, mask provides two hosts per subnet.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 3165