Sawaal

 CCNA Questions

Popular Latest Rated
Q:

Which of the following descriptions about IPv6 is correct?

A) Addresses are not hierarchical and are assigned at random B) Broadcasts have been eliminated and replaced with multicasts
C) There are 2.7 billion addresses D) An interface can only be configured with one IPv6 address
 
Answer & Explanation Answer: B) Broadcasts have been eliminated and replaced with multicasts

Explanation:

There are no broadcasts with IPv6. Unicast , multicast, anycast, global, and link - local unicast are used.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

1 7614
Q:

You have the following binary number :10110111. What are the decimal and hexadecimal equivalents?

A) 69/0x2102 B) 183/B7
C) 173/A6 D) 83/0xC5
 
Answer & Explanation Answer: B) 183/B7

Explanation:

You must be able to take a binary number and convert it into both decimal and hexadecimal. To convert to decimal, just add up the 1s using their values. The values that are turned on with the binary number of 10110111 are 128+32+16+4+2+1=183. To get the hexadecimal equivalent, you need to break the eight binary digits into nibbles (4 bits), 1011 and 0111. By adding up these values, you get 11 and 7. In hexadecimal, 11 is B, so the answer is 0xB7.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

1 7518
Q:

What is the subnetwork address for a host with the IP address 200.10.5.68/28?

A) 200.10.5.56 B) 200.10.5.32
C) 200.10.5.64 D) 200.10.5.0
 
Answer & Explanation Answer: C) 200.10.5.64

Explanation:

This is a pretty simple question. A/28 is 255.255.255.240, which means that our block size is 16 in the fourth octent. 0,16, 32, 48, 64, 80, etc. The host is in the 64 subnet.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

1 7462
Q:

A receiving host has failed to receive all of the segments that it should acknowledge. What can the host do to improve the reliability of this communication session?

A) Send a different source port number B) Restart the virtual circuit
C) Decrease the sequence number D) Decrease the window size
 
Answer & Explanation Answer: D) Decrease the window size

Explanation:

A receiving host can control the transmitter by using flow control ( TCP uses windowing by default). By decreasing the window size, the receiving host can slow down the transmitting host so the receiving host does  not overflow its buffers.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 7443
Q:

An administrator issues the command "ping 127.0.0.1" from the command line prompt on a PC host named PC1. If an ICMP reply is received, what does this confirm?

A. The PC host PC1 has connectivity with a local host
B. The PC host PC1 has connectivity with a Layer 3 device
C. The PC host PC1 has a default gateway correctly configured
D. The PC host PC1 has connectivity up to Layer 5 of the OSI model
E. The PC host PC1 has the TCP/IP protocol stack correctly installed

Answer

Answer : E

Report Error

View answer Workspace Report Error Discuss

Subject: CCNA

11 7407
Q:

The router address 192.168.10.250 is the default gateway for both the Web Server 2 and Host 1. What is the correct subnet mask for this network?

A. 255.255.255.0
B. 255.255.255.192
C. 255.255.255.250
D. 255.255.255.252

Answer

Answer : A

Report Error

View answer Workspace Report Error Discuss

Subject: CCNA

0 7310
Q:

Mention different memories used in a CISCO router ?

Answer

Different Memories used in a CISCO router are as follows :


NVRAM stores the startup configuration file.

DRAM stores the configuration file that is being executed.

Flash Memory – stores the Cisco IOS.

 

Report Error

View answer Workspace Report Error Discuss

Subject: CCNA
Job Role: Network Engineer

26 7284
Q:

To enable OSPFv3, which of the following would you use?

A) Router1 (config - if) # ipv6 ospf 10 area 0.0.0.0 B) Router1 (config - if) # ipv6 router rip 1
C) Router1 (config - if) # ipv6 router eigrp 10 D) Router1 (config - if) # ospf ipv6 10 area 0
 
Answer & Explanation Answer: A) Router1 (config - if) # ipv6 ospf 10 area 0.0.0.0

Explanation:

To enable OSPFv3, you enable the protocol at the interface level as with RIPng. The command string is ipv6 ospf proces-id area area-id.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 7098