Sawaal

 CISCO Certification Questions

Popular Latest Rated
Q:

What is the maximum data rate for the 802.11g standard?

A) 6Mbps B) 11Mbps
C) 22Mbps D) 54Mbps
 
Answer & Explanation Answer: D) 54Mbps

Explanation:

The IEEE 802.11g standard provides a maximum data rate of up to 54Mbps.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 3217
Q:

What must be configured on the network in order for users on the Internet to view web pages located on Web Server 2?

A. On router R2, configure a default static route to the 192.168.10.0 network
B. On router r2, configure DNS to resolve the URL assigned to Web Server 2 to the 192.168.10.20 address
C. On router R1, configure NAT to translate an address on the 209.165.100.0/24 network to 192.168.10.20
D. On router R1, configure DHCP to assign a registered IP address on the 209.165.100.0/24 network to Web Server 2

Answer

Answer : C

Report Error

View answer Workspace Report Error Discuss

Subject: CCNA

0 3184
Q:

What is the full IPv6 address represented by FF02::130F:5?

Answer

FF02:0000:0000:0000:0000:0000:130F:0005

Report Error

View answer Workspace Report Error Discuss

Subject: CCNP

0 3118
Q:

You need the IP address of the devices with which the router has established an adjacency. Also, the retransmit interval and the queue counts for the adjacent routers  need to be  checked. What command will display the required information?

A) show ip eigrp adjacency B) show ip eigrp topology
C) show ip eigrp interfaces D) show ip eigrp neighbors
 
Answer & Explanation Answer: D) show ip eigrp neighbors

Explanation:

The show ip eigrp neighbors command allows you to check the IP addresses as well as the retransmit  interval and queue counts for the neighbors that have established an adjacency.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 3114
Q:

What is the first thing that BGP checks to determine if a prefix is accessible?

Answer

BGP checks the NEXT_HOP attribute to determine if the NEXT_HOP is accessible or in the IP routing table.

Report Error

View answer Workspace Report Error Discuss

Subject: CCNP

5 3107
Q:

If you wanted administrators to see a message when logging into the router, which command would you use?

A) message banner motd B) banner message motd
C) banner motd D) message motd
 
Answer & Explanation Answer: C) banner motd

Explanation:

The typical banner is a message of the day (MOTD) and is set by using the global configuration mode command banner motd.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 3101
Q:

A device on a network is ready to send a frame. What is the first thing that CSMA/CD logic does?

A) Sends a token out to instruct other devices not to send packets. B) Sends a jamming signal out to prevent other hosts from sending packets.
C) Sends a discovery message out to find out if the destination host is on the same subnet. D) Listens to see if the Ethernet is busy.
 
Answer & Explanation Answer: D) Listens to see if the Ethernet is busy.

Explanation:
Report Error

View Answer Report Error Discuss

Filed Under: CCENT

0 3071
Q:

Pat Address Translation is also called what?

A) NAT Fast B) NAT Static
C) NAT Overload D) Overloading Static
 
Answer & Explanation Answer: C) NAT Overload

Explanation:

Another term for port Address Translation is NAT Overload because that is the keyword used to enable port address translation.

Report Error

View Answer Report Error Discuss

Filed Under: CCNA

0 3039